BRYSTON 4B SST MANUAL PDF

BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Mumuro Kazigar
Country: Bahamas
Language: English (Spanish)
Genre: Science
Published (Last): 11 June 2011
Pages: 403
PDF File Size: 13.35 Mb
ePub File Size: 13.57 Mb
ISBN: 573-6-47395-943-3
Downloads: 46615
Price: Free* [*Free Regsitration Required]
Uploader: Kazrakasa

This warranty gives you specific legal rights and you may also have other rights which may vary from province to province and country to country. Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the post knob. Bridged W 8 ohms Max. Graph shows that distortion is essentially unaffected by load. The Output binding posts provide 4 different interconnect options.

Use quality wire, and if runs are more than 3 meters use at least 12 gage wire. Ship the amplifier only in the original packing material, as the unit is not insurable by carriers otherwise. Balanced input Vs Single ended input: The speaker binding posts will accept wire up to 3 gage in size. This will ensure the amplifier is protected in future transport.

For this amnual do not install anything directly above it. Then power the unit up normally.

  HIPERPRZESTRZE MICHIO KAKU PDF

Bryston 4B SST Stereo Amplifier User Manual

Additional tightening pressure can be achieved using a coin in the slots of the knob. This is the home theatre setting for balanced operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less. Different input configurations result in slightly different noise readings. Also see installation section on ventilation.

The most important installation consideration is ventilation. Heat Dissipation 8 ohms – Bridged W 8 ohms Max.

On the rear panel is provided a high current plug for the power cord receptacle. Should the breaker trip, lower or remove the amplifier input signals. Bridge mode is for mono operation. In the manusl event you have a problem and must return it for service you must use the proper packing material. The RED binding post is bryson to the amplifier output. Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical.

See brydton 2 below. Input Sensitivity Gain Switch. Push firmly the center of the switch until the power-up sequence begins. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston. Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink.

Never lift the safety ground to the amplifier nor remove the ground pin from the plug. Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier.

  LIVRO RIZZATTO NUNES PDF

Each channel selects a gain of 29dB 1v or 23dB 2v.

Bryston Stereo Amplifier 4B SST User Guide |

Should thermal shutdown occur, the channel will mute, and the channel LED will turn orange indicating this condition. If both channel LED indicators are unlit the amplifier probably needs only to be powered on. Banana plugs offer a quick disconnect option. Connect to this post the – terminal on the loudspeaker.

Cables should be dressed away from input and power cables. Bryston can provide an optional fan package if required.

Spade lugs provide high contact area and secure fastening. Thermal Shutdown orange Each channel has thermal shutdown circuitry to prevent damage due to overheating.

When the channel has cooled to a safe operating condition the channel will return to normal operation. Momentary clipping can be tolerated, however it indicates that maximum undistorted power has been surpassed and potential speaker damage may result if overload conditions persist.

Installation see rack mounting section if applicable Ventilation. Check that the voltage rating on the label conforms with your locality. The voltage is listed on the label found at the upper right of the rear panel.