Refer to the CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual ( W) for details on programming opera- tions. CPM2C Features and. Part number. Operation manual. CPM2A operation manual. W Programming manual. CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual. All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to an OMRON product, regardless of whether or not it.
|Published (Last):||15 May 2010|
|PDF File Size:||1.83 Mb|
|ePub File Size:||9.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 84 IN through IN have different values. Page 19 EMC Directives. Do- ing so may result in malfunction.
Page numbers refer to the previous version. When connecting the PC to a personal computer or other peripheral device, ei- ther ground the 0-V side of the PC or do not ground the PC at all. Contrast Control The display contrast can be adjusted with the control on the right side of the Pro- gramming Console.
Multiple address monitor 2. Push the PC forward until the lock snaps into place. Page 25 When used as single-phase pulse outputs, there can be two outputs with cpmm2a fre- quency range of 10 Hz to 10 kHz with a fixed duty ratio or 0.
Troubleshooting Flowcharts OFF by more than one instruction e. Not connecting to the correct ground may result in electric shock.
Specifications subject to change without notice. Do not connect bare stranded wires directly to terminals. The password prevents unauthorized access to the program.
Output Short Protection The output or internal circuitry might be damaged when the kanual connected to an output is short-circuited, so it is recommended to install a protective fuse in each This cable cannot be removed. Reading status Check AR comparison in Is input wiring correct? Fatal Errors Unit configuration.
The information contained in this section is important for the safe and reliable application of the Programmable Con- troller. Note If an error occurs while manaul the program, refer to Programming Console Operation Manul for details on correcting the error. The key functions for these Pro- gramming Consoles are identical. Also, the CPM2A CPU Unit is a stand-alone Unit that can han- dle a broad range of machine control applications, so it is ideal for use as a built- in control unit in equipment.
If no errors are found, the following display will appear.
Specifications Terminal screw size Power interrupt time AC power supply: A power interruption may or may not be detected for power interruptions some- what longer than 10 ms for an AC power supply or 2 ms for a DC power supply. Power Supply Wiring Stray wire strands can short-circuit and cause a fire. Before inputting a new program, any error messages recorded in memory should be cleared. Lift up the lock lever. In such a case, a noise filter must be connected to the load side or other appropriate coun- termeasures must be provided external to the PC.
OMRON CPM2A – MANUAL Pdf Download.
Structure And Operation It will be necessary to turn the power off and then on again to enable a new setting if the parameter is ac- cessed only when the power is turned on. Force Set, Reset Multiple address monitor 2. Although some grounding methods short the V side, as shown in the following diagram, nev- er do so with the PC.
Cpm2 B Dimensions All dimensions are in millimeters. Got it, continue to print. Displaying The Cycle Time These differences are caused by changing execution conditions. Functional Ground Terminal Be sure to ground this terminal AC-type PCs only to enhance immunity to noise and reduce the risk of electric shock.
Page 8 Section 4 describes how to connect the Programming Console, and how to perform the various program- manhal operations. Page Authorized Distributor: Page AR ON?
Stray wire strands can short-circuit and cause a fire. If the Programming Console is connected to the PC when PC power is already on, the first display below will indicate the mode the PC was in before the Pro- gramming Console was connected.
Wiring and Connections Section Floor Ducts Leave at least mm between the wiring and the top of the duct, as shown in the following diagram. To print the manual completely, please, download it.
OMRON CPM2A – 11-2005 Manual
Page 40 Functions Listed by Usage Section Usage Function Refer Multiply the input pulse frequency from a high-speed counter by a fixed Pulse synchronization and analog W multiple, convert that value to an analog value, and output as an output function analog manyal.
Hexadecimal, Bcd Data Modification 3. Determine the cause of the error with a Programming Device.