This page contains information about the Owner’s Manual for the ER-1 from Korg. Korg ER-1 Electribe R Rhythm Synthesizer () Drum machine: 8 voices mix of analog modeling and PCM samples with sequencer and Midi sync. Listen to. Check out the Korg Electribe ER-1 Frequently Asked Questions (FAQ) own Patterns in a Pattern Set see page 31 in the ER-1 owners Manual.
|Published (Last):||15 August 2006|
|PDF File Size:||11.98 Mb|
|ePub File Size:||5.84 Mb|
|Price:||Free* [*Free Regsitration Required]|
When you delete a pattern, the event data refer to the follow- ing page at that position will also be deleted. Press the Song mode key to enter Song mode. If you raise the reso- nance and turn the Mqnual knob or adjust EG Int and De- cayyou will hear the typical “meow-ing” sound typical of analog synthesizers. The metronome will sound during playback and record ing.
Doing so may damage the data. If you modify the tempo of a song but then switch to another song without Writing, the first song will return to its original electirbe. To leave MIDI mode, press a different mode key.
Korg Electribe ER-1
Rotate the dial to select the pattern that you wish to edit. Rotate the dial to select the pattern number in which the data will be saved i. Front and rear panel 2. If you re-select a pattern or turn off the power without performing the Write operation, the sound will return to its unedited state.
Convenient functions for editing patterns If you wish to save the pattern you edit using these func- tions, you must perform the Write operation before se- lecting a different pattern or turning off the power. Be aware that if you perform these janual during synchronized playback, the synchro- nization will be lost. Part Select key Each time you press this key, Part 1 and Eledtribe 2 will alternate as the part selected for editing. Raising the Depth excessively may cause the sound to distort.
If you wish to record the other part as well, use the Part Select key to switch parts, and continue recording. Handling To avoid breakage, do not apply excessive force to the switches or controls. B Bank C Bank Eelctribe.
Korg ELECTRIBER ER-1 Owner’s Manual
Knob movements that are event-recorded in Song mode will always playback electrube a way that corresponds to the Smooth type motion sequence setting and not the Trig Hold type.
To defeat this “hold” condition, press the Keyboard function key once again. Here’s how you can make the EA-1 playback in synchronization with the tempo of the ER If the Global mode Memory Protect setting is on, it will not be possible to Write. Rotate the dial to set the Swing value. In Global mode, turn the Protect setting “oFF” p.
If you wish to create a pattern in more detail, use Event Edit refer to p. Basic operation Quick Start Playing the sound of a part along with a song or pattern 1. Adjust the output level of the connected device so that the peak LED lights only at the maximum levels. If you wish to keep the edited song, you must perform the Write operation to save the song data.
The song will begin playing from the pattern of the currently selected position. If you intentionally want to discard your edits and revert to the original pattern data, simply select a different pattern without Writing.
Rotating the knob toward the right will increase the volume. As you listen to the song or pattern, strike the part keys to play along. Repeat steps 4 and 5 to assign as many patterns as you wish. The pitch of OSC1 electribw be the pitch that sounds when you use the keyboard function or the pitch specified for a phrase pattern.
Move kanual knobs and keys of the Synthesizer section to apply filtering or effects to the input signal. Rotating the knob toward the right will increase the level of the delayed sound and the amount of feedback.
The nanual you make in Global mode will be cancelled if you turn off the power without Writing. At this time you can use the Select keys to change the pattern set group indicated by the red select LEDs lower line 1—4, to use 16×4 total of 64 pattern sets.
Korg ER1 factory reset 1. Rotate the dial to modify the pitch of that step. The ER-1 will play the pattern in synchronization with the tempo of the EA The target step will automatically advance by one step each time you do so. With the factory set- tings this will be “2. Slave devices that receive this Start message will synchronize to the Timing Clock messages subsequently received, and will begin playback from the beginning. Saving A Pattern write 4.
At this time, press- ing the PLAY key will not start playback. When the Keyboard function is off, the step key corresponding to the target step will blink.