EUP 8054 PDF

EUP datasheet, EUP circuit, EUP data sheet: EUTECH – Standalone Linear Li-Ion Battery Charger With Thermal Regulation in ThinSOT. EUP Price, EUP Stock, Buy EUP from electronic components distributors. Instant result for EUP Buy Eutech Microelectronics EUP at Win Source. Source EUP Price, Find EUP Datasheet,Check EUP In stock & RFQ from online electronic .

Author: Masida Mazule
Country: Myanmar
Language: English (Spanish)
Genre: Marketing
Published (Last): 17 December 2010
Pages: 80
PDF File Size: 14.7 Mb
ePub File Size: 18.67 Mb
ISBN: 760-8-57472-402-3
Downloads: 7710
Price: Free* [*Free Regsitration Required]
Uploader: JoJozilkree

The thermal dup for the heat generated by the IC is from the die to the copper lead frame, through the package leads, especially the ground lead to the PC board copper. Once the average charge current drops below BAT pin is less than 2. If this voltage drops below the 4.

EUP Eutech Microelectronics|Online Components | WIN SOURCE

CHRG output enters a strong pull-down state during recharge cycles. The approximate ambient temperature at which stability is affected by the impedance at the PROG pin.

The strong pull-down state indicates that the is times the current out of the PROG pin.

The PC board copper is the heat sink. This parameter is not applicable to the EUPX. Therefore, an N-channel has ended. The charge voltage is fixed at 4. When it reaches the 1. The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient. Figure 10 shows that by using two different value pull-up resistors, a microprocessor can detect all three states from this pin. VCC can range from 4. Provides power to the charger.

  LINDA NOCHLIN EL REALISMO PDF

Other heat sources on the board, not related to the chargermust also be considered when designing a PC board layout because they will affect overall temperature rise and epu maximum charge current. Nearly all connected to the charger output.

Provides charge current to the battery and regulates the final float voltage to 4. Open-Drain Charge Status Output.

EUP lithium-ion charger circuit diagram

This feature protects eul EUP from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the EUP Block Diagram DS Ver1.

An internal precision resistor divider from this pin sets the float voltage which is disconnected in shutdown mode. Figure 12 shows an example of how to indicates that a charge cycle is in progress.

The charge current can be set according to typical not worst-case ambient temperature with the assurance that the charger will automatically reduce the current in worst-case conditions.

A new charge cycle can be initiated by reconnecting the program resistor. This pin is also clamped to approximately 2.

Absolute Maximum Ratings are those values beyond which the eyp of the device may be impaired. When charging in constant-current mode, this pin servos to 1V. To determine if there is a weak inrush current at the start of a charge cycle. No series resistor is needed if tantalum capacitors are used. This ensures that the battery is kept at or near a fully charged condition and eliminates the need for periodic charge cycle initiations. State Diagram of a Typical Charge Cycle An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above the undervoltage lockout threshold.

  JOEL MAGAREY PDF

(PDF) EUP8054 Datasheet download

The EUPX does not include this trickle charge feature. Feedthrough vias to inner or backside copper layers are also useful in improving the overall thermal performance of the charger.

In all modes, the voltage on this pin can be used to measure the charge current using the following formula: Driving this pin to voltages beyond the clamp voltage will draw currents as high as1. The the average battery current as shown in Figure 8. The EUP are guaranteed to meet performance specifications from 0 to A charge cycle restarts when the battery voltage falls below 4.

Positive Input Supply Voltage.